The Stanley 10 1/2 Refurb Finished

Stanley 10 1/2 Refurb Finished

here is how it looked when I picked it up at a carboot sale(yard sale) for ยฃ5 ($10)

Cleaning The Plane

First step to assemble the kit needed to use electrolysis to strip the rust off

Pics of the kit

Really expensive kit ๐Ÿ˜€ One gallon plastic container with the top cut off, two bits of iron to act as negative anodes, two old spring clamps to hold the anodes, and a 12v battery charger, and most important two or three spoonfuls of washing soda. ๐Ÿ˜€

Next step fill the container with water turn on the power and add the soda a little at a time until approximately a 5-6 amp current is obtained. ๐Ÿ˜€

Container filled with water the current is turned on and washing soda added

15 minutes later it’s cooking quite nicely ๐Ÿ™‚ the scum on the top is rust.

Here is a closer pic of the lever cap before restoration started

The lever cap had about an hour undergoing the electolysis treatment then I buffed it up using a polishing mop on my grinding machine. This next pic is how it looks now.

At the moment the frog and chip beaker are in tub cooking ๐Ÿ˜€

Tuesday 30th July

The chip breaker had the same elecrolysis treatment but it needed a lot of rubbing down, there is some pitting as I expected but I can live with that

The blade although needing a lot a rubbing down came out much better than the chip breaker

Some clean up shows there is some pitting but nothing that bad

After flattening the sole and sides of the body a little just to get it clean paint stripper was applied
to remove the japaning

For more on how to do japaning see my page “Home made japaning”

 

Here it is finished ๐Ÿ™‚

 

2741213435_f1ddd2b276_b

More bits off the Stanley 10 1/2

Stanley 10 1/2 frog gets it’s first coat of japaning before it gets it’s second coat it will be cooked in the Aga for an hour or two

Bits and pieces polished up and finished

Tote and knob off Stanley 10 1/2

Sanded down and ready for finish

Tote and knob off Stanley 10 1/2 after six coats of french polish every one cut back with 0000 wire wool I was going to leave the final coat gloss but it looked to plastic so I cut that back as well then applied a coat of Black Bison paste wax to finish.

It’s hard to think it’s over 100 years old ๐Ÿ˜€

I’ve Just Been Car Booting

Now was I ripped off or did I rip the seller off?
I don’t really think I was ripped off, infact I think I ripped off the seller, he wanted ยฃ8 I knocked him down to ยฃ5 ๐Ÿ˜€

Yes it’s a very early Stanley 10 1/2 of about 1895-1910ish so well older than me ๐Ÿ˜€

No adjustable front plate like on the very first models and no adjustable frog

Ok it’s well rusty but not pitted, it was so rusty I had to use WD40 to get the cap off

Now this was my last restoration and some will cringe if I do this to the 10 1/2

I wonder what I’ll get for it on ebay? ๐Ÿ˜€

Cleaning The Plane

First step to assemble the kit needed to use electrolysis to strip the rust off

Pics of the kit

Really expensive kit ๐Ÿ˜€ One gallon plastic container with the top cut off, two bits of iron to act as negative anodes, two old spring clamps to hold the anodes, and a 12v battery charger, and most important two or three spoonfuls of washing soda. ๐Ÿ˜€

Next step fill the container with water turn on the power and add the soda a little at a time until approximately a 5-6 amp current is obtained. ๐Ÿ˜€

Container filled with water the current is turned on and washing soda added

15 minutes later it’s cooking quite nicely ๐Ÿ™‚ the scum on the top is rust.

Here is a closer pic of the lever cap before restoration started

The lever cap had about an hour undergoing the electolysis treatment then I buffed it up using a polishing mop on my grinding machine. This next pic is how it looks now.

At the moment the frog and chip beaker are in tub cooking ๐Ÿ˜€

Tuesday 30th July

The chip breaker had the same elecrolysis treatment but it needed a lot of rubbing down, there is some pitting as I expected but I can live with that

The blade although needing a lot a rubbing down came out much better than the chip breaker

Some clean up shows there is some pitting but nothing that bad

After flattening the sole and sides of the body a little just to get it clean paint stripper was applied
to remove the japaning

Washed the stripper off just needs some more cleaning and maybe a little flattening.